Hudco Poly-Grout

High Stregnth Polymer Grout

Description

HUDCO Poly-Grout is a heavy duty non-shrink epoxy grout for installation of industrial equipment. When prepared and installed as recommended, HUDCO Poly-Grout offers the following advantages:

• Long service life
• High resistance to chemical attack
• High resistance to physical degradation
• Exceptional dimensional stability
• Reduced downtime

Uses

• Machinery Grout System
• Concrete Foundation Repair
• Concrete Floor Repair
• Concrete Surface Protection

Properties

• Gel Time*..................................................1 1/2 - 2 hours
• Initial Cure* (approx. 90%)..........................24 hours
• Final Cure*................................................5 - 7 days
• Density, lbs/cu ft.......................................122
• Compressive Strength, PSI.......................14,100
• (ASTM-C579, Method B)
• Modulus of Elasticity, PSI..........................1,400,000
• (ASTM-C579, Method B)
• Shrinkage (ASTM C-883)...........................Passes
• Adhesive Strength:
• Concrete to Concrete (ASTM C-882)...........Concrete Fails
• Steel to Steel, PSI (ASTM-D1002)..............3400
• Flexural Stength, PSI................................6000
• Tensile Strength, PSI (ASTM D638)............6800
• Shelf life (unopened), min.........................2 years

Gel and cure characteristics were determined at 70°F. As with all epoxy polymers, the speed of gel and cure reactions is faster at higher temperatures - and conversely, slower at lower temperatures.

Curing

Initial curing time 24 hours.
Final cure 5-7 days.

Surface Preparation

(A) Surface of substrates must be clean and sound.
(B) Remove grease, oil, or other foreign material with acetone, wire brushing, or sandblasting. Acid etching the surface is acceptable if followed by thorough flushing with clean water. Surface must be dry before applying.

Mixing

Combine HUDCO Poly-Grout Resin with HUDCO Poly-Grout Curing Agent. Mix thoroughly for several minutes making sure all resin is blended with curing agent. Mix blended resin and curing agent with proper amount of HUDCO Poly-Grout Aggregate until wetted (3-5 minutes). All aggregate must be wet with mixed resin and curing agent. For proper mixing add aggregate to blended resin and curing agent.

Packaging

KIT RESIN CURING AGENT AGGREGATE
LB LB. LB.
1/3 Cu. Ft. 4.8 2.6 40.0

Handling Precautions

CAUTION: For Industrial Use Only. Keep Away From Children.

HUDCO Poly-Grout Resin contains epoxy resin which is harmful if swallowed. After prolonged exposure it may irritate skin and cause sensitization and/or dennatitis.

HUDCO Poly-Grout Curing Agent contains organic amine compounds which are harmful if swallowed. After prolonged exposure or repeated skin contact, it may cause irritation, sensitization and/or dennatitis.

Emergency and First Aid Procedures

Eye Contact - Irrigate promptly with clean water for 15 minutes and call a physician.

Skin Contact - Wash with soap and water promptly.

Inhalation - Remove to fresh air and provide oxygen if necessary.

lngestion - Call a physician at once. Give milk or white of egg beaten with water. Then give a tablespoon of salt in a glass of warm water to induce vomiting.

Protection Procedures

If used in a confined or an enclosed area, use an air supplied mask or respirator with canister for organic vapors and provide mechanical exhaust ventilation. Use protective gloves, safety glasses, and protective clothing. Avoid contact with skin and clothing. Contaminated clothing should be laundered before wearing again. Contaminated shoes should be thoroughly cleaned before wearing again.

Warranty

Because the storage, handling and application of these materials are beyond our control, we can accept no liability for the results of their use. Our liability is limited only to replacement- of any material proven defective in manufacture. We suggest users try small applications to determine the suitability of the product for their intended use.