Hudco CMP Metal Fast

HUDCO CMP Metal Fast is machinable and provides excellent results in emergency situations. It offers the only fast-curing ceramic-metal polymer repair system that has superior bond, high performance strength and excellent storage stability. At 75° F, it “gels” in approximately 3 minutes and will cure hard enough to be machined in 15 minutes to 1 hour (depending upon “heat sink” of part).

Typical Applications

HUDCO CMP METAL FAST Enables Fast Emergency Repairs To:

 

  • Cracked Castings
  • Scored Shafts
  • Damaged Hydraulic Rams
  • Valve Bodies
  • Leaky Pipes
  • Stripped Threads

Typical Applications

HUDCO CMP METAL FAST Enables Fast Emergency Repairs To:

 

  • Cracked Castings
  • Scored Shafts
  • Damaged Hydraulic Rams
  • Valve Bodies
  • Leaky Pipes
  • Stripped Threads

Physical Properties

Mixing Ratio (R:H)
2:1 by Weight
Color
Grey
Initial Curing Time
45 min. @ 75° F
Final Curing Time
24 hours @ 75° F
Gel Time
6 Min. @ 75° F
Pot Life
3 Min. @ 75° F
Lap Shear Strength
3,450 PSI
Compressive Strength
10,400 PSI
Specific Gravity
1.74 Mixed
Temperature Max
200° F

Physical Properties


MIXING RATIO (R:H)
      • 2:1 BY WEIGHT

COLOR
      • GREY

INITIAL CURING TIME
      • 45 MIN @ 75° F

FINAL CURING TIME
      • 24 HOURS @ 75° F

GEL TIME
      • 6 Min. @ 75° F

POT LIFE
      • 3 Min. @ 75° F

LAP SHEAR STRENGTH
      • 3,450 PSI

COMPRESSIVE STRENGTH
      • 10,400 PSI

SPECIFIC GRAVITY
      • 1.74 MIXED

TEMPERATURE MAX
      • 200° F

Resin
Curing Agent
Coverage
Kit Weight
Resin
0.42 lbs. x 4
Curing Agent
0.21 lbs x 4
Coverage
5.08 Sq. Ft. @ 1/16" Thick
Kit Weight
5 lbs.
Resin
Curing Agent
Coverage
Kit Weight
Resin
0.42 lbs. x 4
Curing Agent
0.21 lbs x 4
Coverage
5.08 Sq. Ft. @ 1/16" Thick
Kit Weight
5 lbs.

Call For A Product Consultation

Surface Preparation:

 

(A) Surface of substrates must be clean and sound. Remove grease, oil, or other foreign material with acetone, wire brushing, or sandblasting. Acid etching the surface is acceptable if followed by thorough flushing with clean water.
(B) Roughen surface by grinding or sandblasting (3-5 mil surface profile) Surface must be completely dry with a minimum surface temperature of 75° F before applying.

 

Mixing: Mix 2 parts of HUDCO CMP Metal Fast Resin to 1 part of HUDCO CMP Metal Fast Hardener by weight. Kits are supplied in the correct ratio. Ensure that the sides of the mixing container are scraped into the mixture. Mix several minutes, until consistent color is achieved.

 

Application: Apply product to prepared surface and use supplied tools to achieve desired finish.

 

Curing:At 75°F, product will gel in 3 minutes. Initial cure will occur in 45 minutes. Final Cure occurs in 24 hours. Curing can be accelerated by heating the applied product to 140°F. Product properties will also be improved by curing at this elevated temperature.
CAUTION:

For Industrial Use Only. Keep Away From Children.

HUDCO CMP Metal Fast Resin contains epoxy resin which is harmful if swallowed. After prolonged exposure it may irritate skin and cause sensitization and/or dermatitis.
HUDCO CMP Metal Fast Curing Agent contains organic amine compounds which are harmful if swallowed. After prolonged exposure or repeated skin contact it may cause irritation, sensitization and/or dermatitis.

 

Emergency and First Aid Procedures
  • Eye Contact – Irrigate with clean water for 15 minutes and call a physician.
  • Skin Contact – Wash with soap and water.
  • Inhalation – Remove to fresh air and provide oxygen if necessary.
  • Ingestion – Call a physician at once. Give milk or white of egg beaten with water. Then give a teaspoon of salt in a glass of warm water to induce vomiting.

 

Protection Procedures
If used in a confined or an enclosed area, use an air supplied mask or respirator with canister for organic vapors and provide mechanical exhaust ventilation. Use protective gloves, safety glasses, and protective clothing. Avoid contact with skin and clothing. Contaminated clothing should be laundered before wearing again. Contaminated shoes should be thoroughly cleaned before wearing again.

HUDCO CMP Metal Fast Resin and Curing Agent should be stored in a cool, dry area. Shelf life is a minimum of one year in unopened containers when stored at 70° F – 85° F.

Because the storage, handling and application of these materials are beyond our control, we can accept no liability for the results of their use. Our liability is limited only to replacement of any material proven defective in manufacture. We suggest users try small applications to determine the suitability of the product for their intended use.